Keep in mind that some router models (especially older routers) do allow you to set up the router as a repeater natively, which means you don’t need to use DD-WRT.
Feb 26, 2012 · I am using a TP-Link TD-W8960N as my main router with ADSL connection. It works fine but on the top floor our signal is pretty low. I want to us the Thomson SpeedTouch TG587nv2 (O2 Wireless box IV) as a secondary wireless repeater. I can't use a ethernet cable between them. I want to make a wireless bridge or use WDS. According to TP-Link's instructions, I could hit the WPS button on my router and the Wi-Fi Clone button on the second adapter to set the adapter's settings to my router's network name and password. May 31, 2019 · You can use a LAN cable to extend the Wi-Fi connection to another router. However, that’s not always practical, especially if the location of the second router is far away from the first one. That’s why it’s best to connect the repeater to your original router via Wi-Fi. The process is the same for most TP-link Wireless routers. You need to connect the second router to the first using an ethernet cable from a LAN port on router 1 to a LAN port on router 2. Think of Router 1 as being in charge of the network, and so turn off the DHCP on router 2, let router one do al the work. Apr 19, 2012 · I have a Linksys M10 (Valet) router as my primary router. I have an old Linksys WRT54G Router that I wanted to use as a repeater/second router. Is there any way to use this as a second router without connecting the two via Ethernet, nor putting custom firmware (e.g DD-WRT) on the router?
Now Router B, when connected to Router A using a network cable, will work as a both a switch (allowing you to use its LAN port to add wired devices to the network) and an access point.
Nov 28, 2016 · The example below is how to set up a Router as a Wireless Repeater. The DGND3700 here will be the Base Station and WNDR3800 as the repeater. Base Station Set up (DGDN3700) SSID : specify a name that you can use to distinguish the Base Station from other wireless networks in the area. > Set the MAIN router to only serve out IP's from 192.168.0.3 - 192.168.0.99 > Set the 2ND router to serve out IP address from 192.168.0.125 - 192.168.0.255 > Tried disabling DCHP on 2ND router > Tried setting 2ND router to "Enable Wireless Repeater" and set the Base to my MAIN router IP adress of 192.168.0.1 So far nothing I have tried has worked.
Apr 13, 2020 · A second router provides more open Ethernet ports so that additional computers can join the network. Support for mixed wired and wireless network setups : If you have a wired home network and want to connect Wi-Fi devices to it, installing a wireless router as the second router allows those devices to connect while allowing the rest of the
Can you use a second router as a wifi extender? You can easily extend your Wi-Fi network with additional networking hardware like Wi-Fi repeaters and Wireless Access Points. The other inexpensive option is that you get hold of an old wireless router, one that is longer in use, and connect it to your existing (main) router using an Ethernet Apr 10, 2018 · Turning a router into an access point or repeater is mainly for when you want a “middle man” method to connect to a network. For example, you may not be able to connect your WiFi to Router A due to distance or obstacles in the way, so you want to put Router B between your computer and Router A and have it “pass along” your WiFi signal. Assign the Old Router a Fixed IP Address. The router you use for your repeater needs its own IP address. 1. Go to the LAN setup page and give the router an IP address in the range assigned by the main router but outside automatically issued addresses from DHCP (Dynamic Host Communications Protocol). Decide which frequency band you are going to use in Repeater mode. Both frequency bands in Repeater mode will still broadcast and clients will be able to connect to either of those frequency bands. You can edit the wireless settings in the Wireless widget for both frequency bands. If your main router or access point is single-band: Jul 06, 2015 · B: Configure the Second Router as a Repeater. Step 4: Next we need to configure SLAVE, our second router. First reset the router to factory defaults by hard-pressing the reset button with a pin for about 10 seconds. Now connect the SLAVE router to your computer using the physical Ethernet cable.